Search results

Yeh I thought about changing the gearing to go faster... But to be honest i don't want to try beat top speeds... It was just a test to see how the new motor goes... It actually needs more bottom end because when coming out of tight corners in 2nd you need to clutch fan it to get the revs up...

Thanks for the advice on emailing Motorbike City... I am emailing them now... But I just realised there is a brand or something on the side... It says 'Guo Ying' I tried to google it but nothing really came up...

Farrk!! That sucks dude... Next time ill wear some extra gear =) Hahaha... Yes! This weekend... So look out for a new vid ;) Either did I... I was expecting like 85-90 km/h or so... I wonder how much faster it will go if i buy an OKO FlatSlide Carbie hehe

Thanks for the replies guys... But these taps wont work.. All the moto shops ive been into only had them ones but the rubber seals are different... If you look at them they have a 3 Square rubber seal instead of the single O-Ring on mine...

Just did a measure with a ruler so not 100% accurate but its about 39mm center of eye to eye and 45mm end to end (If that makes any sense to you lol)

Hey guys... I have a 2007 Motovert Pro and the fuel tap broke on it and I am having trouble finding one to replace it... In the mean time I have bought an after market CRF50 tank but my shrouds do not line up and will not bolt onto the tank... Does anyone know where I can buy a fuel tap like...

Yeh I thought about editing it but then you get the haters on youtube saying its fake etc lol And hey... I had a helmet on =)

Testing the top speed on my 2007 Motovert Pro with my new 2010 GPX 125 Race Engine... Top Speed = 99.5km/h Enjoy =) <object width="640" height="385"><param name="movie" value="http://www.youtube.com/v/0LqbiXOUxfk?fs=1&amp;hl=en_US"></param><param name="allowFullScreen"...

They are Marzocchi

Hey guys... Just after a new Front Brake Setup for my 2007 Motovert Pro... Does anyone know of any good setups that will fit? And where from? I have some pics below... My Disk is 190mm and I did measure the gap between the 2 bolt eyes but I lost the paper i wrote it on and my bike is at a...

Thanks for the info... I would rather buy the carby from DHZ but I want to try and get it tomorrow... More questions for you.... =) Instead of waiting for it in the post I thought I might drive to Motorbike City in Slacks Creek... Is that an ok shop? What size jets does the 26mm carby...

Thanks... I was reading this in another thread earlier... Ive got a question though... What are the K's before the jet numbers? and what is a JJH Needle?

I honestly don't care... As long as it works and works well... I'm the kind of person that would rather go all out and buy the best even if it is over kill because i feel that it is better then buying something average and then it breaking or later upgrading and spending more $$ I would buy it...

Woops!! Double Post

Yeh true... The one I have is really annoying though... The idle screw is at the very bottom... So there is no way to get a screw driver in to adjust it while the bike is running... So I have to keep pulling the whole carby off and then adjusting it then put it all back on... It is very time...

Thanks for the quick reply... I just had a bit of a look around reguarding the OKO Flate Slate 26mm and had a read of this thread: http://www.miniriders.com.au/carby-tuning/23986-those-about-rock-buying-oko-flatslides.html It seems too tech for me.. I am not a pro rider and pretty much...

Hey guys... I have a 2007 Motovert Pro and I have just put in a GPX 125 motor... The carby I am currently using isn't running properly and is annoying me.. I think its sucking too much air because when i stick my finger in the air intake hole and block off how much air is going in, It idles...

Is there any tutorials out there on how to set the timing right when putting a new piston & rings in?? I have a Lifan 140cc and need to put a new Piston & Ring kit on... and need help!! Thanks to anyone who can help me out here ;)

Hello... just wondering if anyone knows where i can get a user manual for a 2007 Motovert Pro 140cc... or if there even is one out there? I am going to pull the engine down and what to make sure i do it right Thanks :D

woops double post