Search results

I sort of know what you are saying. I'm gunna run dc led lights off the battery. I want to first work out what the current is at 12v so then I can order the lights. Amps x volts will give me the power in watts. I don't want to draw to much off the battery.

It's a 4 pin for single phase. I have it wired the same as above and testing red wire to ground. I tested r/r and diode is ok. I think I'll investegate again this avo.

Hmm thinking about this my theory is (+ AC Current in from stator coil on yellow wire. Passes positively charged electrons through diode to red wire which goes to battery. Expels excess voltage and through ground wire. Then The negitive electrons flow though white wire which goes to the...

Cheers for the info. I had a rectifier on an old quad. I joined the yellow and white together and plugged it into the yellow wire from the coil. Hooked up multimeter and I ran the bike and got these results. DC 7v 5amp at idle. At 3/4 throttle I got 19v DC and 9amp. Hmm not regulating too well...

I have a single yellow wire.

I've never needed lights or thought of having them till I went riding in the stato the other night. I had a dolphin torch strapped to the front but it gave poor visibility. I nearly was bitten by a snake on a track as I failed to see it till I rode past and it stuck at me. Anyways I want...

Thanks for the reply. I put the B at 9 o'clock, bolted it up, started it up, and fanged the crap out of it! Alls great

Hi I have a z155 with an outer rotor kit with a v2 race head. I have a cam sprocket that has 2 marks either end. On the tn race cam there is a b stamped between the 2 threaded holes and on the other side between the 2 theaded holes there's a non threaded hole. My question is which was dose the b...

Yeah seen that thead a few times. I think I got a s35 cam. Very aggressive up top likes the throttle. It don't cruze to well at mid range when ya just putting along. It sort of don't suit the scrub riding id do only when ya racing ya mate around

Got a z155 tb v2race head tb race piston plus 30mm to 27mm manifold. I have 2 carbs oko 28mm and a 30mm oko. 28oko is real, 30mm is fake. I can use the guts out of the real 28mm in the 30mm. Which one should i use? Any one using these set up? What's ya jets and needle clip if so?

Lol I would have done the same....

Measure the the outsid diameter of the carby and ya will know what size to get. I would say if the bikes been sitting awhile the pilot jet may be blocked. When fuel sits in a carby too long it breakers down and will coat the bowl of ya carby in this brown crap wich is a pain to get out and...

Hmmmmm I'm having a problem with d

Sweeeeeeeet I was gunna use my tb race piston out of my yx, same size od 60mm this will be ok yer? I'm doing a full ground up rebuil on my bike, blasted the frame on the weekend and got the first coat of Kawasaki green on it today. Looks soooooo bloody good. I haven ridden the bike for over 8...

Hi all got a yx160 with a bugged bottom end so I got a spare engine which is a pisterpro Z155. Will my V2 race head off my yx160 fit the z155?

Sounds like your old head may of had a bent valve, but you did the right thing by buying a new head than mucking around reseating new valves. Carefully take your rings off ya piston ans insert them one at a time in the bore. Then use ya piston and put the rings down a little so it squares the...

Cheers guys I didn't think about wreckers. I found one for $44 complete exhaust. Looks like it maybe a later model one as my 88 has a big chunky muffler and this is a longer one. Next thing is to muck around with the baffle. Still researching on what to do with the baffle to get a bit more flow...

What a excellent deal mate it shows that if ya spend the time treasure hunting it pays off!

Just picked up a honda xr200 1988 model. Only thing is the exhaust is cactus! Anyone know what else may got this bike like a crf150 exhaust that I can modify or maybe a china bike exhaust modified to fit. New exhausts are way too much and finding a cheap second hand stock exhaust is hard to...

Can you install a gauge for tunning the carb on a pit bike? If so whats the process if any one knows? I see them for about $20 online and thought it would be handy.