yx160

hey everyone its loco... lol :P now as the title says "Daytona Anima clutches"......... ive got the yx160... with the 5 plate clutch... i was wondering if the daytona 6 plate clutch unit itself would hook right on? considering the zs160/155 has a "daytona style" clutch unit.. and the yx's and...

Hey guys and girls... I'm looking some cheap bling ie: brake lever and gear lever I'm looking at a 11mm spline gear lever to go on a yx160....??? Manly red anodized.. Saw a red gear lever on eBay in China for 17 bucks.. Any suggestions? Also wanna get rid of the flimsy brake lever.... Cheers loco

So a good few months ago, my bike was not dropping into second gear and had to skip to third. Finally it jammed in 2nd and there goes my bike. Troy at Rocko said too expensive to fix. I have fitted both new gear shafts(damaged) with original kick start, clutch plates, piston. everything...

hey peoples ive come to that part of my build were i need a full exhasut from header to muffler i love the yoshimura setus that dhz sell but am unsure if they will fit with my crf70 type dhz outlaw frame my setup is just a gpx yx160 motor and need help in finding out what fits with my frame...

hey peoples just scored a genuine vm26 running the following jets main:190 pilot:22.5 ill be installing it on a gpx yx160 out of a pitsterpro only mods on engine are inner rotor kit and big bore exhaust what do people suggest for a good jetting? never buggered around with jetting before regards

Hey all I gotta get a new LHS engine case for me yx 160. Anyone know if there's differences in them? I read a post in hear a while back where someone got a new one and put the motor back together and had shifting problems. What I remember is it came down to a casing mismatch. Anyone shine some...

Racing NGK Ignition Coil Pack 110cc 125cc 150cc 250cc ATV PIT PRO Dirt Quad Bike | eBay is it a legitimate ngk and would it need a splitfire lead as well?

Could someone plz explain how I go about stroking my 160 to 184 what do I exactly need to do so?

ive got another thread related to a rec reg setup..... http://www.miniriders.com/ask-tech-masters/38211-how-setup-rec-reg-kit.html gday lads and laddies so i put the coil on.. which was supplied by my67xr.. thanks again . anyway my new coil is generating 3.5V and i was thinking i need...

Hey guys, So my chain flew off on my lifan 125 and snapped the pulse sensor off. So I bought a new stator plate. It seemed to be exactly the same except the sensor was a tiny bit closer to the flywheel and I had to grind about half a mil off the 'nib' of flywheel so it wouldn't hit when it...

Do they use irk, ork, or a regular stator? I ask this because I was on pitbikeclub's website and I asked this question. They said that I can put a 155cc stator on 125cc engine to give my bike better throttle response.

Can you replace a stock bike with a new stator and because of that new stator it has better throttle response/acceleration? Like are there "performance" stators and flywheels? and I dont mean and ORK or IRK.

http://www.youtube.com/watch?v=ILvFDhWWdFE

Hi guys New to the forum, have a problem with my genuine thumpstar engine, i recently replaced the stock magneto with one of those performance magnetos off ebay, but i cannot for the life of me get spark. ive replaced the coil, spark plug, and try every possible combination of wiring here...

Bought an aftermarket stator/flywheel and all on eBay (link below). Swapped it into my lifan 110cc no problem, accept for the wiring... Has anyone done such a swap? Do I need to buy a new harness all together? Does anyone have a diagram for this stator, or know what colors match up? I've always...

hi there just realised i have the wrong stator, what i want to do is run lights off my yx 160 but there is no 'yellow' wires only black with yellow and that goes to the coil So....i have the regulator and im wondering if i can hard wire the regulator to the coil? if not ive seen a magneto on dhz...

Hey guys, I am looking at buying a yx160 for my bro's build, and also looking at the possibilities of rebuilding it in the future with the spares I have. So in effect my question is: Will a GPX 155z/160ho Head, Cylinder & Piston, fit on a yx160 bottom end? If not, what would I have...

This is just a basic guide (in fact my first 4S build) so don't take this as gospel and please feel free to add bits i may of missed or got wrong... Anyway lets start by pulling down the YX160. Fisrt of all i would prep the new head with the cam, rockers + tappets and arms. Start by fitting...

finally starting a thread on my new/used Atomik Fuse it came with a dead 125 lifan, (broken gearbox and casings) i originally bought it for parts, brakes etc, but knew it wouldnt take much to get it up and running. i pulled the 150 (1P56FMJ) out of the Orion, (my customising my Orion...

Bike Silencer How can i silence my pitster pro so that it doesn't annoy the neighbors?