What bike is this?

Discussion in 'General Chat' started by tribute3, Nov 5, 2017.

Mini Dirt Bikes

Help Support Mini Dirt Bikes:

  1. Nov 5, 2017 #1

    tribute3

    tribute3

    tribute3

    New Member

    Joined:
    Nov 5, 2017
    Messages:
    3
    Likes Received:
    0
    Hey guys,

    I aquired a mystery bike. Need help identifying it because it'll need new parts. Compression seems low. It runs for a few cycles then shuts off. Can't seem to get it to run consistebtly and I been screwing with the carb screws. Kick start is pretty easy to kick over also.

    The engine says 86ml. I suspect is a Chinese brand bike, check out the pics.

    "Engine Number" is 03053258 as stamped on the frame.

    Thanks!
     

    Attached Files:

    • 01.jpg
      01.jpg
      File size:
      88.4 KB
      Views:
      16
    • 02.jpg
      02.jpg
      File size:
      110.5 KB
      Views:
      5
    • 03.jpg
      03.jpg
      File size:
      110.9 KB
      Views:
      7
    • 04.jpg
      04.jpg
      File size:
      86 KB
      Views:
      6
  2. Nov 8, 2017 #2

    motodevo

    motodevo

    motodevo

    Miniriders OG Master Spanner Spinner

    Joined:
    Sep 19, 2007
    Messages:
    663
    Likes Received:
    24
    Location:
    in the shed
    Definitely Chinese. If you need a new piston/rings most chinese 86/90cc motors use a 47mm piston (same as a stock stroke 70/72cc). The engine number on the bottom of the motor on the chain side below the sprocket will confirm this if it has a 47 in the first 4 or 5 numbers (eg IP47########).
     
  3. Nov 10, 2017 #3

    gottagetacheaperhobby

    gottagetacheaperhobby

    gottagetacheaperhobby

    Moderator

    Joined:
    Jun 13, 2013
    Messages:
    3,138
    Likes Received:
    16
    Location:
    stowport tas
    Will be difficult to tune the carb while there is no air filter on it, it would be very lean ATM. Bang a lightly oiled unifilter on it, and check valve lash before you go looking at the piston and rings.

    Sent from my ALCATEL_4034A using Tapatalk
     
  4. Nov 10, 2017 #4

    tribute3

    tribute3

    tribute3

    New Member

    Joined:
    Nov 5, 2017
    Messages:
    3
    Likes Received:
    0
    Great Info, thank you...
     
  5. Nov 10, 2017 #5

    tribute3

    tribute3

    tribute3

    New Member

    Joined:
    Nov 5, 2017
    Messages:
    3
    Likes Received:
    0
    Thats the plan...
    It was in rough shape, but it turns over fine.
    My plan is to do the following:
    Valve adjustment
    Timing
    Spark plug gap
    Oil change
    and overhaul the carb

    I hope itll start after all this!

    I'm using a Honda CT90 Manual for reference. I'm not sure how similar it will be just yet.
    unfortunately, I don't really have a compression measurement tool. I'm not keen on buying one since Ill probably never use it again.
     
  6. Apr 20, 2018 #6

    bmxreeves

    bmxreeves

    bmxreeves

    Member

    Joined:
    Apr 20, 2018
    Messages:
    11
    Likes Received:
    0
    Check your valves. The ones on my bike got tight you could kick it by hand. and wouldn't idle/ run on the bottom end.
     
  7. Jul 17, 2018 #7

    jonathanpg

    jonathanpg

    jonathanpg

    Member

    Joined:
    Jan 10, 2018
    Messages:
    16
    Likes Received:
    0
    1p47 engine just the stroke different, Lifan Zongshen 1P47 parts can fit
     

Share This Page



arrow_white