Search results

UPDATE Put in that electric kit from tbolt and man this F'er rips!!!!!! Problem solved!!!

He bought it off ebay so I'm sure it was the cheapest one he could find I think i am going to order this full system just to get it over with so I don't have more issues in the future and I know exactly what in dealing with .TRC Outer Rotor IgnitionUltimate Full System - Pit Bike Engine Parts...

About 50 degrees here in minnesota

So do I need a new stator/source coil?

Ok out testing electronics so far and here's what I have come up with Checked stator- set @ 2000ohms. Blue/white wire and green a checked at 97.7 ohms Source coil-set @ 2000 ohms. Black/red wire and green checked at 338 ohms Primary coil windings- set @200 ohms black/yellow + wire/terminal...

This is what I'll be doing.... STATOR: (Once you have the ignition cover off) Visual test: Inspect the coil bar , if you see any bulges or discoloration its likley worn out Voltage Meter will be set on AC for testing output The stator should have 80-100VAC (usually black/red) Set meter to...

Thanks I have a buddy with a pitster, idk what carb he has in it but I'm going to rob it off his bike and give it a try. I'll be testing my whole electrical system tonight with multimeter is there anything inpetticular I should look for?

Right. Do u know where to buy parts for this carb?

Leaking out top vent but mostly leaking through the hole on the inside face of the carb that leads to float needle Yes I can see light through it it is clean as can be. The reason I'm considering getting a mikuni Is I can't find parts for this carb I cannot re drill the rubber on the float...

Yes I took everything apart blew every hole with compressed air and I used gauge pins from my work to stick in jets that fit perfect. I looked at them through a microscope too and they are plenty clean. Maybe I should put new jets in it? I need a new float needle anyway because it keeps pissin...

Mikuni VM 26mm Carb VM26-606 - Pit Bike Engine Parts - CARBS and JETS - TBW0399 - TBolt USA, LLC And this carb

.TRC Outer Rotor IgnitionUltimate Full System - Pit Bike Engine Parts - Electrical - TRC-0650 - TBolt USA, LLC Should I just say f it and order this lol

Once I get soark again and if it doesn't rev I will try pulling the head. The bike ran fine before the kid put new wiring system in it but it's been siting for a year. Got it pretty cheap was just hoping it would be a simple fix lol but it turned into a mess

I can pick up a multimeter tomarow to test it. Also I checked the pickup clearance to the nob on the flywheel and it is very close but not touching. I'm debating in just buying a whole new wiring kit for this and a new mikuni carb. I might save myself some headaches but then again I might...

So when I bought the bike from my buddy he told me he just put in new outer rotor full kit with flywheel and new CDI. He never got it to run right after that. He told me it was a liftan kit off ebay. I went through all his wiring and I am sure it's right. The bikes only dirty from trying to...

Now I can't even get it started plug out kicking it by hand and I see no sparky :(

Case looks like the bottom pic

1/4 turn throttle it spitts sputters and bogs. Won't rev up at all past 1/4 turn even slowly.

Believe it or not I just took bike for a ride and it doesn't seem any better at all! Here's a pic of my plug man this things getting on my nerves Thank you for any help u can give me

Got it all together put gas line on and now it's pissin out gas. Took it apart and cleaned float needle about 7 times lol the rubber on the tip of the needle looks a little worn and deformed in going to try to find a new one just not sure where to get parts for this carb