Minibiker's 160 build(ciniworx)

[minibiker]

My asv's and seat had arrived but got sent the wrong seat so sending it back and have to wait for the other one to arrive, will probably have the bike finished tomorow night

[/URL][/IMG]

 

[motovert24]

Is that the $59asv set? Been thinking of getting a set

 

[8r3nd0]

They're copies right!

 

[minibiker]

Is that the $59asv set? Been thinking of getting a set

Yeah i got them for $45 cause my mate works at a motorbike shop

They're copies right!

Yeah they are

 

[minibiker]

Got much more done today also got the asv levers on and pro taper grips, but having alittle problem with the bike it idles then slowly the idle starts getting slower and stalls and after that when i rev it the idle stays abit high. Also started putting my other bike back together.

[/URL][/IMG]

[/URL][/IMG]

 

[Blender]

i have the same problem with my fakuni 26mm. i've been told when they idle unevenly they are in need of a rebuild. could be wrong, i have no idea lol, i just adjust it if i gets to low or high. what carb is currently on the bike now? and also did you get your sub-frame repaired?

 

[minibiker]

i have the same problem with my fakuni 26mm. i've been told when they idle unevenly they are in need of a rebuild. could be wrong, i have no idea lol, i just adjust it if i gets to low or high. what carb is currently on the bike now? and also did you get your sub-frame repaired?

It has a oko26 and it was idling perfect before i pulled it apart

 

[8r3nd0]

I'd say check you throttle cable is moving freely and the carb slide is free. Did you take the carb off at all?
You might have a air leak between the carb and manifold.

 

[minibiker]

I'd say check you throttle cable is moving freely and the carb slide is free. Did you take the carb off at all?
You might have a air leak between the carb and manifold.

will check it tomorow !

 

[minibiker]

Managed to get the bike going properly after realising that the rubber manifold which holds the carbi had rips in it maybe from me over tightening it haha whoops luckily i had a brand new spared one now i know not to over tighten it. Basically nearly done after i recieve my seat and will probs use the old graphics until i choose a new graphics kit.

[/URL][/IMG]

[/URL][/IMG]

 

[motovert24]

I hate those, Annoying as when they crack. Mine usually split from the metal. Tb manifolds one is million times better but only works with the v2 head I think. Wouldn't mine it on my daytona

 

[minibiker]

Was thinking of getting this sticker kit with red plastics and white front number plate as ive seen it done on a klx110 style pitbike and it actually looked pretty good and got my eye, couldnt think of any other graphics that would look good. What do ya's reckon?

http://www.ebay.com.au/itm/New3M-gr..._Parts_Accessories&hash=item35c9f0855e&_uhb=1

[/URL][/IMG]

 

[motovert24]

I reckon it'll be good, haven't seen one yet

 

[Blender]

i reckon there nice mate. there simple and not cluttered which most graphics look bad because of

 

[nickv1980]

Those rubber manifolds are the worst quality ever ! I used to break them all the time ... the one that came with my PE 28 carb is mint it bolts up different through the front instead of the back and the rubber is a lot better quality haven't split one yet

 

[coolmodee01]

was this jess cini's bike?

there a good thing i've got one of course chuck an elka shock in the back tune it and you wont look back

cleaning up nice hey

 

[minibiker]

i reckon there nice mate. there simple and not cluttered which most graphics look bad because of

Yeah they are

Those rubber manifolds are the worst quality ever ! I used to break them all the time ... the one that came with my PE 28 carb is mint it bolts up different through the front instead of the back and the rubber is a lot better quality haven't split one yet

I think its because i over tightened it haha but yeah your right they are rubbish

was this jess cini's bike?

there a good thing i've got one of course chuck an elka shock in the back tune it and you wont look back

cleaning up nice hey

Yeh

I reckon it'll be good, haven't seen one yet

Yeah same just have to wait and see!

 

[minibiker]

Put her all back together today, just waiting on a new seat and graphics and bashplate now. First time it ever started first kick on me today and was a lot more responsive (maybe set it up better than i did on the other bike hmm).

[/URL][/IMG]

 

[s2rt85]

looks good mate

 

[minibiker]

Thanks mate. Got my seat today

[/URL][/IMG]